Silicon-Power-Diode 5A, (U) 50V, blocking-diode. When adding LED rear tail light / turn signal combinations in addition to bulb original tail lights, it can happen that a small leakage current flows from the brake line, when the Rear light cable is connected or vice versa.
For example we have just had a supplementary LED rear light switch off when the brake light cables are connected.
To prevent this, a 5A blocking diode in series is connected to the brake light cable in a way that the current can flow to the new LED tail light but not back. The silver bar on the diode marks the direction to where the electricity can flow.
Save cutting wires by using these indicator adapter leads which convert from OEM plugs to aftermarket bullet connectors.
The ultra compact Motogadget Push Button Mini Switch is used for operating and setting all instruments. Designed for you to enclose in a housing.
These indicator relays are for halogen incandescent bulb indicators not LED. They are suitable for 8-23w bulbs by selection. Please choose the model with the same connectors as standard and for the bulb wattage you are using.
Selection of spare leads for the Maximiser 360T.
LED Rear Light Can-Bus Compensator Resistor Lead for motorbikes with CAN-bus electrical system such as the BMW R1200GS which may show an error if a LED tail light is mounted.
This small chrome horn runs on 12Volts, it is 70 mm in diameter and is NOT E-marked.
LED Motorbike indicators work with a lower wattage than standard bulb type indicators. To avoid rapid flashing it may be necessary to replace the existing relay with a specially designed LED relay correcting the wattage.
If you are only changing one pair of indicators eg the rear, you can use inline resistors, these are required for each indicator.
The selection you make below changes the image to show that choice..
This 100dB black steel horn runs on 12V, it is 70 mm in diameter and is E-marked road legal.
This 100dB Stainless steel horn runs on 12V, it is 72 mm in diameter and is E-marked road legal.
This 12v DC Universal Switching Relay has a maximum 30A current load. Comes with a rubber slide on mount..
Shrink Sleeve Solder Connector Red 25 Pack for cable cross section from 0.5 to 1.5 mm2..
The simple, fast solution for tension-resistant, moisture-proof cable connections. Simply insert the appropriately stripped cables into the suitable connector and then melt the solder ring with a hot air gun. Then heat the connector with the hot air gun until the adhesive emerges at the ends.
Shrink Sleeve Solder Connector Blue 25 Pack for cable cross section from 1.5 to 2.5 mm2..
This large chrome horn runs on 12Volts, it is 100 mm in diameter and is NOT E-marked.
Square Type Waterproof Horn Push Button Switch also suitable for an engine cutout. Momentary make switch with 2 wire connection.
22mm Handlebar mount Round Type Horn Push Button Switch also suitable for an engine cutout, or e.g. override on ATV/Quad, waterproof protective cap.
Momentary make switch with 2 wire connection.
Momentary engine circuit breaker with round push button switch. Comes with a clamp for 22 mm handlebars and a length of twin wire with fitttings.
Can also be used for a horn etc..
Triumph Thruxton 1200 and Thruxton 1200R/RS 2016 onwards Highsider tail tidy adapter cable.
Motogadget compact push button switch for operating and controlling all instruments. Also used as replacement push-button for the m-Switch.
The push-buttons are a high quality, very robust design and vibration- and spraywater proof (IP65). The ergonomic pressure point provides feedback when operating.
This 110dB black steel Italian style horn runs on 12V, it is 80 mm in diameter and is E-marked road legal.
Motorcycle Light on / off switch with clamp for mounting on handlebar.
Note: The required ON/ OFF switch is not included, please order additional item no 240-044
The Motopgadget mo.lock NFC connection cable is a high quality, 2m long, 3-wire cable for connecting the mo.lock NFC and fits the cable cover included with the mo.lock.
These On Off Motorcycle Handlebar Switches come in two versions, contact made and contact broken when in the 'ON' position.
Can be used as a cut out switch or auxiliary lighting, may need a relay for the latter.
Small traditional style handle bar indicator and horn switch, comes with a stainless steel cover.
This powerful USB charger has a 2.1amp output suitable for devices such as phones, tablets and sat navs. It is powered from a 12V battery system of a car, motorcycle, boat etc.
This Oxford High Power 3 Amp USB Type A Charging Kit is to seamlessly integrate your choice of USB charger with your motorcycle. Mount your charging port somewhere convenient using the included 3M™ sticky pad then simply run the attached ring leads directly to your battery terminals.
This Oxford High Power 3 Amp USB Type C (small connector) Charging Kit is to seamlessly integrate your choice of USB charger with your motorcycle. Mount your charging port somewhere convenient using the included 3M™ sticky pad then simply run the attached ring leads directly to your battery terminals.
From BikeIt this SAE Power Supply has twin USB outlets being one standard USB one smaller Type-c, it also has an On/Off switch and a battery volts display.
Typically fitted to off road bikes this Bike It Universal stop or kill switch comes with a hand tether.
Two versions available either circuit breaks (typ. Japanese MX) or the circuit makes (typ KTM MX) when the tether is pulled off.
